Power Supply Board for HP LaserJet MFP 136 / 138 / 108 Original Imported

Original Power Supply Board for HP LaserJet MFP 136 / 138 / 108 — Imported

Get your HP LaserJet back to life with the PRM Original Power Supply Board. This is a genuine original board — not a compatible copy — sourced from original equipment and imported directly. One board fits the entire HP 136/138/108 series.

Looking for an HP 136nw power supply, HP 138fnw power board, or HP 108w power supply? This is the correct power supply board for the entire range.

When Do You Need a New Power Supply Board?
The power supply board converts mains AC power into the regulated DC voltages that run every component inside your printer — the formatter, fuser, motor, scanner, and WiFi module. When it fails, the entire printer is affected. Replace your power supply when you see:
- Printer completely dead — no lights, no display, no response when pressing the power button
- Printer turns on briefly then shuts off immediately
- Random shutdowns during printing — printer dies mid-job
- Fuser error messages — the power supply feeds the fuser heater; a weak supply causes temperature errors
- Burning smell from the power supply area (not from the fuser)
- Printer takes unusually long to warm up or never reaches ready state
- WiFi module not powering on — printer drops off the wireless network (108w / 136nw / 136w / 138fnw)
- Error lights blinking in a pattern that indicates a power fault
- Scanner lamp not turning on during scan/copy (136 / 138 series)
- Tripping your office power switch when the printer turns on

If you've checked the power cable, tried a different wall socket, and the printer still won't power on or keeps shutting down — the power supply board is almost certainly the cause.

1. One Board Fits the Entire 108/136/138 Range: This power supply board is compatible across the HP LaserJet 108a, 108w, MFP 136a, 136w, 136nw, MFP 138fnw, and 138pnw. Same board, same connectors — works in all models whether USB-only or WiFi.

2. Original, Not Compatible: This is a genuine original HP power supply board — the same board that came inside your printer from the factory. Original boards offer exact voltage regulation and long-term reliability that compatible copies cannot match. For a critical component like the power supply that feeds every part of your printer, original is the right choice.

3. Fixes the "Dead Printer" Problem: The most common power supply failure symptom is a completely dead printer — no lights, no response. The HP 108/136/138 series are among HP's newest budget laser printers in India. Before you assume a new printer is failing, a power supply replacement brings it back to life at a fraction of the cost.

4. Resolves Fuser Errors Without Replacing the Fuser: Many fuser errors on the 108/136/138 are actually power supply problems — the board can't deliver enough power to heat the fuser properly. If you've already replaced the fuser and still get temperature errors, the power supply is the fix.

5. Restores WiFi and All MFP Functions: The power supply feeds every component — formatter, fuser, motor, scanner, WiFi module. A failing supply can cause seemingly unrelated problems across print, scan, copy, and wireless connectivity. A new board restores stable power to everything.

6. Easy Installation: Disconnect the printer from mains power, remove the side/rear panels, unplug the connectors from the old power supply board, swap in the new one, reconnect all cables, and reassemble. 20-30 minutes for any printer technician. Basic screwdriver needed.

7. Tested Before Shipping: Every PRM power supply board is tested for correct voltage output before dispatch. Backed by our testing warranty.

Compatible Printers:
HP: LaserJet 108a, 108w, LaserJet MFP 136a, 136w, 136nw, LaserJet MFP 138fnw, 138pnw

Also known as: HP 136 Power Supply, HP 138 Power Board, HP 108 Power Supply Board, HP 136nw Power Supply, HP 138fnw Power Board, HP 108w SMPS Board, HP 136 SMPS, HP 138 Power Supply